Bosch · Dishwasher

Bosch Dishwasher E15 Error Code: Water in the Base (Leak Protection)

Also shown as: E:15, F15, E3100, Flashing tap / water-protection symbol

E15

E15 means Bosch's leak-protection system found water in the base tray of the dishwasher. Turn off the water supply first. You can inspect hoses for visible damage, but Bosch advises against repairing the cause yourself if it isn't obvious.

Moderate⏱ 15 min to inspect; repair variesUpdated 2026-11-18

What E15 means

A float switch in the base pan detected water. The leak-protection (AquaStop / water-protection) system activated and stopped the dishwasher from filling. Some newer models show E3100 instead. The water itself came from somewhere — the code tells you a leak happened, not where.

Likely causes (most → least common)

  1. Leaking or damaged hose / connectionMost common

    Bosch suggests checking the base and hoses for visible kinks, damage or leaks.

  2. Water escaping inside the unit (seal, pump or valve area)Common

    An internal leak drips into the base pan. Locating it requires removing panels — a technician task per Bosch.

  3. Faulty float switchRare

    If the base is dry and E15 persists, the switch itself may be at fault — diagnose with a technician.

How to fix it, step by step

  1. Turn off the water supply

    Close the tap or valve that feeds the dishwasher. This is Bosch's first instruction for E15.

    Easy⏱ 2 min🔧 No tools
  2. Switch the dishwasher off at its button

    Use the on/off button. Bosch Switzerland notes that AquaStop needs power to protect against flooding, so they advise not to unplug it while it is in this state — follow your manual.

    Easy⏱ 1 min🔧 No tools
  3. Look for visible leaks and damaged hoses

    Check the floor around the base and, where accessible (under the sink), the inlet and drain hoses for kinks, cracks or loose connections.

    Easy⏱ 10 min🔧 Flashlight, Towels
  4. Replace an obviously damaged hose — or book service

    If a hose is visibly damaged, Bosch recommends ordering the genuine replacement part. If no cause is visible or the error persists, Bosch advises against self-repair and recommends booking a repair.

    Moderate⏱ 30–60 min🔧 Screwdriver set, Towels / bucket

When to call a professional

  • No visible leak or damaged hose — the water came from inside the unit.
  • E15 returns after a hose was replaced.
  • Water has reached flooring, cabinets or electrical outlets.

Parts that may be involved

Always match the part to your exact model number. Buttons below are placeholders until affiliate partnerships are approved.

AquaStop inlet hose (model-specific)

Replaces a damaged AquaStop / inlet hose — Bosch explicitly mentions ordering replacements for visibly damaged hoses.

Fit: Use the model's E-Nr. (on the door edge) to match.

No price shown — prices are only listed when verified on a retailer page.

Drain hose

Replace a cracked or leaking drain hose.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Float switch / leak sensor

Only if a technician confirms a faulty switch.

Fit: Model-specific; diagnose first.

No price shown — prices are only listed when verified on a retailer page.

Related codes

FAQ

Can I reset a Bosch E15 error myself?

The code clears once the base pan is dry and the cause is fixed. Bosch's guidance is to turn off the water, check for visible hose damage, and book a repair if the cause is not visible — rather than forcing a reset.

Is E3100 the same as E15?

Yes. Bosch lists E3100 with the same meaning — water detected in the base, leak protection activated.

Should I unplug the dishwasher?

Bosch Switzerland advises switching it off at the button but not unplugging it, because the AquaStop system needs power to keep protecting against water damage. Check your manual.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.