Samsung · Washer
Samsung Washer 4C Error Code: Water Not Filling — Causes & Fixes
Also shown as: 4E, nF, 1 4C (on some top-loaders)
4C means your Samsung washer is not getting enough water. In most homes it is a closed or half-open tap, a kinked supply hose, or a clogged inlet mesh filter — all fixable in under 30 minutes without tools beyond pliers.
What 4C means
The washer tried to fill but did not detect the expected amount of water within its time limit. Samsung groups 4C with 4E and nF (older or different displays) as a water-supply / not-filling error. Note that a variant like 4C2, 4E2 or nF1 is a different problem: the hot and cold hoses are swapped.
Likely causes (most → least common)
- Water tap not fully openMost common
One or both supply valves are closed or only partly open, or were turned off for maintenance and never reopened.
- Kinked, bent or damaged supply hoseCommon
Pushing the washer back against the wall can fold the inlet hose and choke the flow.
- Clogged inlet mesh filtersCommon
Small screens where the hose meets the washer catch sediment and scale. Samsung recommends cleaning them at least twice a year.
- Low household water pressure or frozen pipesOccasional
Samsung UK states the supply must be between 0.5 and 8 bar. Frozen hoses in unheated rooms also trigger 4C.
- Hot supply not connectedOccasional (US top/front loaders)
If only cold is connected, the washer can throw a fill error when it asks for hot water — even on some cycles labelled Cold.
- Drain hose pushed too far into the standpipeOccasional
If the drain hose sits too deep or seals the standpipe, water can siphon out while filling. Samsung US says roughly 6 inches (and not more than 8) into the pipe.
- Faulty water inlet valve or control boardRare
If supply, hoses and filters are fine and 4C persists, the inlet valve (or its wiring/board) may have failed.
How to fix it, step by step
Open both water taps fully
Turn the hot and cold supply valves fully counter-clockwise and leave them open while the washer runs.
Check the supply hoses for kinks
Unplug the washer, pull it forward carefully and make sure neither inlet hose is folded, crushed or damaged. Confirm hot goes to hot (red) and cold to cold (blue).
Power-cycle the washer
Unplug the washer (or switch off its breaker) for about one minute, restore power and start a short cycle.
Clean the inlet mesh filters
Turn off both taps, put a towel down, unscrew the hoses from the back of the washer, gently pull out the small mesh screens with pliers and rinse them under running water (an old toothbrush helps). Refit, reconnect and check for leaks after opening the taps.
Check the detergent drawer
Samsung notes a clogged dispenser drawer can occasionally cause 4C. Remove the drawer, clear residue and refit it.
Check the drain hose position
The drain hose should hook into the standpipe without sealing it and should not be pushed in deeper than about 6–8 inches. Do not remove the hose holder screw on the back of the washer.
When to call a professional
- 4C keeps coming back after taps, hoses, filters and drain position are all confirmed OK.
- You hear the washer clicking or humming at fill time but no water enters (possible inlet valve failure).
- Water leaks from inside the cabinet or you see damaged wiring.
Parts that may be involved
Always match the part to your exact model number. Buttons below are placeholders until affiliate partnerships are approved.
Water inlet valve (model-specific)
Replaces a valve that no longer opens when supply, hoses and filters are confirmed fine.
Fit: Must match your exact model number (sticker inside the door or on the back).
No price shown — prices are only listed when verified on a retailer page.
Washer inlet hoses (pair)
Replace kinked, cracked or bulging hoses. Samsung US advises against 'flood-safe' style hoses on its washers.
Fit: Standard 3/4" hose thread in North America; check length.
No price shown — prices are only listed when verified on a retailer page.
Inlet hose screen / filter
Replace a torn or corroded mesh screen.
Fit: Often included with the inlet valve or hose kit.
No price shown — prices are only listed when verified on a retailer page.
Related codes
FAQ
Can I still use my Samsung washer with a 4C error?
Not until water can enter. Once the tap, hose or filter problem is fixed, the error clears when you restart a cycle. Samsung notes buttons may be locked for about 3 minutes after the code appears on some models.
Is 4C the same as 4E?
Yes — Samsung lists 4C, 4E and nF as the same water-supply error on different models and displays.
What does 4C2 mean?
4C2 (also 4E2, nF1 or CE on some models) means the cold inlet is receiving hot water — the hoses are swapped. Reconnect hot to hot and cold to cold; Samsung says no service is needed.
Sources
This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.
- Samsung washing machine information and error codes — Samsung US (last checked 2026-11-18)
- How to resolve a 4E or 4C error code on a washing machine — Samsung UK (last checked 2026-11-18)
- Check out the information codes on my washing machine — Samsung Ireland (last checked 2026-11-18)