LG · Washer

LG Washer IE Error Code: Not Filling With Water — Causes & Fixes

Also shown as: Water Inlet Error, No Water Supply

IE

IE is LG's water inlet error: the washer did not fill to the right level in time. Usually a tap is not fully open, a hose is kinked or frozen, or the inlet filter is clogged. A drain hose sitting too low can also siphon water out as it fills.

Easy⏱ 10–40 minUpdated 2026-11-18

What IE means

LG shows IE when the tub does not reach the required water level within a set time — LG's front-load guide puts it at 8 minutes without enough water. The washer either got too little water or lost it as fast as it came in.

Likely causes (most → least common)

  1. Tap closed or not fully open / water supply interruptedMost common

    Check other taps in the house first — a supply outage looks exactly like a washer fault. Installers sometimes leave the valve closed.

  2. Kinked or squashed inlet hoseVery common

    Vibration can push the washer back and pinch the hose against the wall.

  3. Clogged inlet filterCommon

    A small screen inside the hose connection on the washer collects rust, sand and scale.

  4. Frozen tap or hoseSeasonal

    In freezing weather the supply line or hose can freeze solid.

  5. Drain hose too low or submerged (siphoning)Common after installation

    If the drain hose has slipped out of its holder or its end sits under water, water drains as fast as it fills. On top-loaders, LG warns that pushing the drain hose more than 4 in (10 cm) into the drainpipe causes siphoning.

  6. Hot and cold hoses on the wrong tapsOccasional

    LG asks you to check cold (blue) and hot (orange/red) hoses are on the matching valves.

  7. Failed water inlet valve (solenoid)Less common

    If all checks pass, LG says the inlet valve may have failed and needs service.

How to fix it, step by step

  1. Open the taps fully

    Turn both water valves counter-clockwise until fully open, and confirm water flows from another tap in the house.

    Easy⏱ 2 min🔧 No tools
  2. Straighten the inlet hoses

    Pull the washer out slightly and remove any kinks or pinches. Replace a hose that is cracked or bulging.

    Easy⏱ 5 min🔧 No tools
  3. Thaw frozen lines (cold weather)

    LG suggests wrapping the tap in a towel soaked in hot water (around 50–60 °C / 122–140 °F) for about 5 minutes. A disconnected hose can be warmed in water no hotter than 50 °C.

    Easy⏱ 15–30 min🔧 Towel, Bucket of warm water
  4. Clean the inlet filter

    Turn off the tap and unplug the washer. Unscrew the supply hose from the back of the washer, pull the filter out with pliers and scrub it under running water with a toothbrush. Refit the filter before reconnecting the hose.

    Easy⏱ 15 min🔧 Pliers, Old toothbrush, Towel
  5. Check the drain hose position

    Make sure the drain hose end is not under water and is still clipped into its holder. On top-loaders, it should not go deeper than 4 in (10 cm) into the drainpipe.

    Easy⏱ 5 min🔧 No tools
  6. Run a test cycle

    Restart a cycle and listen for water entering in the first minutes. If IE returns, request a repair.

    Easy⏱ 10 min🔧 No tools

When to call a professional

  • IE persists with taps fully open, clean filters, straight hoses and a correctly placed drain hose.
  • You hear the valve click but no water enters, or water enters very slowly despite good house pressure — LG points to the inlet valve.
  • The tap itself will not open or leaks when turned.

Parts that may be involved

Always match the part to your exact model number. Buttons below are placeholders until affiliate partnerships are approved.

Inlet hose set (hot/cold)

Replace hoses that are kinked permanently, cracked or bulging.

Fit: Standard 3/4" garden-hose thread on most US models; check your region and model.

No price shown — prices are only listed when verified on a retailer page.

Inlet filter screen

If the screen is torn or will not come clean.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Water inlet valve (model-specific)

For a failed solenoid valve — usually a technician job.

Fit: Match model number exactly.

No price shown — prices are only listed when verified on a retailer page.

Related codes

FAQ

What does IE mean on an LG washer?

Water Inlet Error: the tub did not fill to the required level within the set time.

Can the drain hose cause an IE code?

Yes. If the drain hose is too low, out of its holder or submerged, water drains out while filling, so the washer never reaches its level. LG lists this as a cause on front-loaders and warns about deep drainpipe insertion on top-loaders.

How long does LG wait before showing IE?

LG's front-load guide says IE appears if there is not enough water in the tub after 8 minutes.

Does a cold winter cause IE?

It can. Frozen taps or hoses stop water completely. Once they thaw, the washer fills normally again.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.