LG · Dishwasher

LG Dishwasher AE Error Code: Leak Detected — Causes & Fixes

Also shown as: E1, FE, RE

AE

AE (E1 on some models) means water has reached the base of your LG dishwasher and lifted the leak float switch. LG's usual suspects: too much detergent or dish soap, a dirty door gasket, a blocked spray arm or an unlevel unit. You then dry the base pan to clear it.

Moderate⏱ 30 min + 24–48 h dryingUpdated 2026-11-18

What AE means

A float switch in the base pan rises when water collects there. LG's dishwasher guide says the unit then keeps draining to protect the appliance and your floor. The same family of codes (FE/AE/RE) can also mean too much water came in.

Likely causes (most → least common)

  1. Too much or wrong detergentMost common

    More than one pod or tablet, a dispenser filled beyond its lines, or hand dishwashing liquid all create foam that overflows. LG says never to use dishwashing liquid.

  2. Food or grease on the door gasketCommon

    Build-up stops the door sealing so water escapes into the base.

  3. Blocked or damaged spray armCommon

    Debris can deflect spray toward the door seal.

  4. Dishwasher not levelCommon

    LG tests this by pouring about a gallon of water into the tub and seeing whether it pools to one side.

  5. Water poured into the Heat Dry blower (Dynamic Heat Dry models)Model-specific

    LG warns not to confuse the Heat Dry filter cap with the water-softener cap.

  6. Torn door seal, damaged spray arm or internal leakLess common

    LG says these need service.

How to fix it, step by step

  1. Check what detergent you used

    Use only one pod/tablet, or liquid/powder up to the dispenser lines — LG's guide: line 15 for light soil or soft water, line 25 for heavy soil or hard water. Never use hand dish soap.

    Easy⏱ 2 min🔧 No tools
  2. Clean the door gasket

    Wipe food and grease off the gasket and the tub surface it seals against. Look for tears.

    Easy⏱ 10 min🔧 Damp cloth
  3. Clean the spray arms

    Remove the spray arms and clean them with a soft brush and warm soapy water, then refit.

    Easy⏱ 15 min🔧 Soft brush
  4. Check the level

    Put a spirit level against the top, sides and floor of the tub, or remove the lower rack and pour in about a gallon of water to see if it pools to one side.

    Moderate⏱ 15 min🔧 Spirit level, Jug of water
  5. Dry the base pan

    Turn off the dishwasher's circuit breaker. Remove the two screws on the kick plate at the bottom and take it off. Soak up any water in the base. If the base is hard to reach, LG suggests leaving the kick plate off for 24–48 hours so it can evaporate.

    Moderate⏱ 20 min + 24–48 h🔧 Phillips screwdriver, Towels or sponge
  6. Reset and test

    Switch the breaker off and back on to reset, then run an empty cycle and watch for leaks.

    Easy⏱ 1–2 h🔧 No tools

When to call a professional

  • AE/E1 comes back while you are using one pod or the correct dose.
  • The door seal is torn or a spray arm is damaged.
  • There is no water on the floor but the error persists — LG advises unplugging and requesting service.
  • LG's guide also says to request service if the unit is not level and you cannot level it yourself, and if you poured water into the Heat Dry blower of a built-in unit (do not pull it out).

Parts that may be involved

Always match the part to your exact model number. Buttons below are placeholders until affiliate partnerships are approved.

Door gasket (model-specific)

Replace a torn or deformed seal.

Fit: Match model number.

No price shown — prices are only listed when verified on a retailer page.

Lower / upper spray arm

If an arm is cracked or its nozzles are damaged.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Dishwasher detergent pods

One pod per load avoids overdosing.

Fit: Any automatic-dishwasher detergent; never hand dish soap.

No price shown — prices are only listed when verified on a retailer page.

Related codes

FAQ

What does AE mean on an LG dishwasher?

Water has collected in the base and activated the leak float switch. You need to find the cause and dry the base before the dishwasher will work normally again.

How do I reset an LG dishwasher AE error?

Dry the base pan (turn off the breaker, remove the kick plate, soak up water or let it evaporate for 24–48 hours), then turn the breaker off and on and run an empty cycle.

Is E1 the same as AE?

Yes — LG uses AE or E1 for the leak/float-switch condition depending on model.

Can dish soap trigger AE?

Yes. LG says dishwashing liquid is far too concentrated and produces enough bubbles to overflow into the base.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.