Frigidaire · Dishwasher

Frigidaire Dishwasher i20 Error Code: Did Not Drain — Causes & Fixes

Also shown as: I20

i20

i20 means your Frigidaire dishwasher did not drain completely. Frigidaire's checklist: disposal knockout plug removed, drain hose not blocked or pinched, hose at least 32 in above the floor, and glass trap/filter clear of food soil.

Easy⏱ 15–45 minUpdated 2026-11-18

What i20 means

The dishwasher could not pump the water out fully by the end of the drain phase.

Likely causes (most → least common)

  1. Glass trap or filter clogged with food soilMost common

    Debris in the filter and sump area slows draining.

  2. Drain hose blocked, pinched or restrictedVery common

    Crushed under the sink or clogged inside.

  3. Disposal knockout plug still in placeCommon after installation

    A new garbage disposal ships with its dishwasher inlet sealed.

  4. Drain hose too lowCommon

    Frigidaire specifies the drain hose must reach at least 32 in from the floor.

  5. Pump or control faultLess common

    If i20 returns after the checks, contact Frigidaire.

How to fix it, step by step

  1. Clean the glass trap and filter

    Remove the lower rack, take out the glass trap and filter, rinse them and remove any food soil from the sump area.

    Easy⏱ 10 min🔧 Soft brush, Gloves
  2. Check the drain hose

    Under the sink, make sure the hose is not pinched, kinked or blocked.

    Easy⏱ 10 min🔧 Flashlight
  3. Check the hose height

    The hose must rise to at least 32 in (about 81 cm) from the floor — usually by looping it up under the countertop.

    Easy⏱ 5 min🔧 Tape measure, Cable tie or hose clip
  4. Check the disposal knockout plug

    If the dishwasher drains into a garbage disposal, make sure the knockout plug was removed.

    Moderate⏱ 10 min🔧 Screwdriver, Hammer
  5. Reset

    Frigidaire lists three ways: press/hold Cancel, turn power off at the breaker, or unplug for 3 minutes. Then run a cycle.

    Easy⏱ 5 min🔧 No tools

When to call a professional

  • i20 returns after cleaning the filter and checking hose, height and disposal plug.
  • Water remains in the tub even after a reset and a drain attempt.
  • You see water leaking under the dishwasher.

Parts that may be involved

Always match the part to your exact model number. Buttons below are placeholders until affiliate partnerships are approved.

Filter / glass trap assembly (model-specific)

If cracked or not locking.

Fit: Match model number.

No price shown — prices are only listed when verified on a retailer page.

Drain hose

Replace if crushed or split.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Drain pump (model-specific)

For a diagnosed pump failure.

Fit: Technician diagnosis recommended.

No price shown — prices are only listed when verified on a retailer page.

Related codes

FAQ

What does i20 mean on a Frigidaire dishwasher?

The unit did not drain completely.

How do I reset i20?

Press/hold Cancel, switch off at the breaker, or unplug the dishwasher for 3 minutes — after fixing the cause.

How high does the Frigidaire drain hose need to be?

At least 32 inches from the floor, per Frigidaire.

Is i40 the same as i20?

No. Frigidaire uses i40 for a clogged filter or sump; i20 is a general did-not-drain code. A dirty filter can cause both.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.